Altium Designer快捷键

0.快捷键中文汇总[摘自:http://bbs.21ic.com/icview-763534-1-1.html]

旋转：Space；
X轴镜像：X；
Y轴镜像：Y；
板层管理：L；
栅格设置：G；
单位进制切换：Q；

对齐-水平：A，D；
对齐-垂直：A，I，I，Enter；
对齐-顶部：A，T；
对齐-底部：A，B；
对齐-左侧：A，L；
对齐-右侧：A，R；

设计-类设置：D，C;
设计-板层管理：D，K；
设计-规则：D，R；
设计-规则向导：D，W；
设计-拷贝ROOM格式：D，M，C；
设计-放置ROOM：D，M，R；
设计-根据选择对象定义板子形状：D，S，D；
设计-编辑网络：D，N，N；

编辑-删除：E，D；
编辑-切断轨迹：E，K；
编辑-设定原点：E，O，S；
编辑-复位原点：E，O，R；

移动-移动：M，M；
移动-拖拽：M，D；
移动-器件：M，C；
移动-打断走线：M，B；
移动-器件翻转板层：M，I；

网络-显示网络：N，S，N；
网络-显示器件：N，S，O；
网络-显示全部：N，S，A；
网络-隐藏网络：N，H，N；
网络-隐藏器件：N，H，O；
网络-隐藏全部：N，H，A；

放置-坐标：P，O；
放置-焊盘：P，P；
放置-字符：P，S；
放置-过孔：P，V；
放置-多边形：P，R；
放置-填充：P，F；
放置-敷铜：P，G；
放置-线性尺寸：P，D，L；
放置-走线：P，T；
放置-差分对布线：P，I；
放置-多根布线：P，M，Enter；

选择-全选：S，A；
选择-线选：S，L；
选择-区域（内部）：S，I；
选择-区域（外部）：S，O；

工具-交叉探测对象：T，C；(+Ctrl:跳转到目标文件)            
工具-泪滴选项：T，E；
工具-设计规则检查：T，D；
工具-复位错误标志：T，M；
工具-从选择元素创建板剪切：T，V，B
工具-网络等长调节：T，R；

取消布线-全部：U，A；
取消布线-网络：U，N；
取消布线-连接：U，C；
取消布线-器件：U，O；
取消布线-ROOM：U，R；

查看-合适区域：V，A；
查看-翻转板子：V，B；
查看-适合文件：V，D；
查看-合适板子：V，F；
查看-合适图纸：V，H；

测距：Ctrl + M；

清除蒙板：  Shift + Ｃ；
查找相似对象： Shift + F;
显示走线长度：  Shift + G；
单层显示：  Shift + S；
改变走线模式：Shift + Space；

切换二维显示：2(主键盘)；
切换三维显示：3(主键盘)；
顶层底层切换：*(小键盘 )；
板层切换： +/-(小键盘)；
智能走线：在放置走线状态，+ Ctrl；

移动多边形顶点：右键，Y，V；
器件联合：右键，U；

增大弧度：长按 >；
减小弧度：长按 <；
减小多根交互式布线间距：长按Shift + B；
增加多根交互式布线间距：长按Shift + B；

3D模式下：
0°旋转：0（主键盘）；
90°旋转：9（主键盘）；

布等长线状态下：
增加蛇形线拐角弧度：1；
减少蛇形线拐角弧度：2；
增加蛇形线宽度：3；
减少蛇形线宽度：4；
增加蛇形线拐角振幅：。；
减少蛇形线拐角振幅：，；

Altium Designer14 SCH快捷键：

对齐-水平：A，D；
对齐-垂直：A，I；
对齐-顶部：A，T；
对齐-底部：A，B；
对齐-左侧：A，L；
对齐-右侧：A，R；

打破线：E，W；

放置总线：P，B；
放置总线入库：P，U；
放置节点：P，J；
放置网络标号：P，N；
放置端口：P，R；
放置字符串：P，T；
放置走线：P，W；
放置线：P，D，L；
放置差分对标示：P，V，F；
放置Blanket：P，V，L；
放置网络类：P，V，C；

从原理图选择PCB器件： T，S；
封装管理器：T，G；
强制标注所有器件：T，N；

查看-合适区域：V，A；
查看-适合文件：V，D；
查看-合适板子：V，F；

清除蒙板：  Shift + C；
改变走线模式：Shift + Space

0.Schematic Editor Shortcuts

G Cycle through snap grid settings
F2 Edit in-place
CTRL + PAGE DOWN Fit all objects into view
SPACEBAR Rotate counterclockwise by 90 degrees while moving an object
SPACEBAR Toggle start/end mode while placing a wire/bus/line
, SPACEBAR Toggle pen color while using highlighting pens
SHIFT + SPACEBAR Rotate clockwise by 90 degrees while moving an object
SHIFT + SPACEBAR Cycle Step through placement modes while placing a wire/bus/line
CTRL + SPACEBAR Rotate counterclockwise by 90 degrees while dragging an object
SHIFT + CTRL + SPACEBAR Rotate clockwise by 90 degrees while dragging an object
, CTRL + Left-click on port or sheet entry Highlight connection/net on target sheet while using highlighting pens
SHIFT + CTRL + C Clear all highlighting applied by highlighting pens
BACKSPACE Remove the last vertex when placing a wire/bus/line/polygon
Left-click, hold + DELETE When a wire is selected to delete a vertex
Left-click, hold + INSERT When a wire is selected to add a vertex
CTRL + Left-click & drag Drag object
Left-click in Navigator panel Cross probe to object on schematic document
ALT + Left-click in Navigator panel Cross probe to object on both schematic document and PCB
ALT + Left-click on net object Highlight all elements in net on sheet
CTRL + Double Left-click On sheet symbol to descend hierarchy
CTRL + Double Left-click On port to ascend hierarchy
+ (numeric keypad) Enlarge IEEE symbol size during placement or movement
- (numeric keypad) Reduce IEEE symbol size during placement or movement
CTRL + F Find text
CTRL + H Find and replace text
F3 Find next occurrence of searched text
INSERT Copy attributes of object under the cursor while placing an object of the same type
S Swap sheet entry side while moving one or more selected sheet entries
V Reverse sheet entry order while moving two or more selected sheet entries
T Toggle sheet entry IO type while moving one or more selected sheet entries
T Toggle all sheet entry IO types while resizing selected sheet symbol
T, P Access Schematic - General page of Preferences dialog

1.PCB Editor Shortcuts

SHIFT + R Cycle through three routing modes (ignore, avoid or push obstacle)
SHIFT + E Toggle electrical grid on/off
SHIFT + B Build Query
SHIFT + PAGE UP Zoom-in in small increments
SHIFT + PAGE DOWN Zoom-out in small increments
CTRL + PAGE UP Zoom-in to 400%
CTRL + PAGE DOWN Fit document into view
CTRL + END Jump to defined relative origin for the workspace
ALT + END Redraw current layer only
ALT + INSERT Paste on current layer
CTRL + G Pop up Snap Grid dialog
G Pop up Snap Grid menu
N Hide the ratsnest while moving a component
L Flip component being moved to other side of board
SHIFT + F1 Pressed while routing, displays the appropriate interactive routing shortcut keys
TAB Pressed while routing, length tuning, component or string placement displays appropriate interactive editing dialog
F2 Display Board Insight and Heads Up display options
CTRL + Left-click Highlight routed net under cursor (repeat in free space to clear)
CTRL + SPACEBAR Cycle through connection lines modes during interactive routing
BACKSPACE Remove last track corner during interactive routing
SHIFT + S Toggle single layer mode on/off (or cycle through Single Layer Modes set in PCB Preferences: Board Insight Display)
O, D, D, O, ENTER Set all primitives to display in draft mode
O, D, F, O, ENTER Set all primitives to display in final mode
O, D (or CTRL + D) Access Show/Hide page of View Configurations dialog
L Access Board Layers And Colors page of View Configurations dialog
CTRL + H Select connected copper
CTRL + SHIFT + Left-click & hold Break track
SHIFT + CTRL + Left-click Highlight additional routed net under cursor
+ (numeric keypad) Next layer
- (numeric keypad) Previous layer
CTRL + Click Highlights layer content on layer tabs
CTRL + SHIFT + Click Increments highlighting on layer tabs
CTRL + ALT + Mouse Hovers highlight layer on layer tabs
* (numeric keypad) Next routing layer
M Display Move sub-menu
ALT Hold to temporarily switch from avoid-obstacle to ignore-obstacle mode
CTRL Hold to temporarily disable electrical grid while routing
CTRL + M Measure distance
SPACEBAR (in interactive process) Rotate object anti-clockwise (define rotation step on PCB Editor - General page of Preferences dialog)
SPACEBAR (during interactive routing) Toggle start/end mode
SHIFT + SPACEBAR (in interactive process) Rotate object being moved clockwise
SHIFT + SPACEBAR (during interactive routing) Step through corner modes during interactive routing
[ Decrease mask level for permanent filter
] Increase mask level for permanent filter
ALT ← View previous component for active library document
ALT → View next component for active library document
Q Toggle units (metric/imperial)
Ctrl + Q Toggle units (metric/imperial) within an open PCB Editor dialog
T, B Access 3D Body Manager dialog
T, P Access Preferences dialog
BACKSPACE Remove last interactive length tuning segment
SPACEBAR Next interactive length tuning wave pattern
SHIFT + SPACEBAR Previous interactive length tuning tuning pattern
SHIFT + R Toggle Routing Mode
, (comma) Decrease interactive length tuning pattern amplitude by one increment
. (full stop / period) Increase interactive length tuning pattern amplitude by one increment
1 Decrease interactive length tuning miter or radius
2 Increase interactive length tuning miter or radius
3 Decrease interactive length tuning pattern gap by increment
4 Increase interactive length tuning pattern gap by increment
Y Toggle interactive length tuning amplitude direction

2.Interactive Routing Shortcuts

Shift+F1 (or ~ (tilde)) Display list of shortcuts
CTRL
+ Click		 Auto-complete segments to target
BACKSPACE Remove last segment
ESC Terminate current trace
SHIFT
+ A		 Add accordion sections (interactive length tuning)
SHIFT
+ C		 Toggle auto-complete
SHIFT
+ G		 Toggle length tuning gauge
SHIFT
+ O		 Toggle visible routing area
SHIFT
+ P		 Toggle Push mode
SHIFT
+ Q		 Toggle glossing
SHIFT
+ R		 Toggle routing mode
SHIFT
+ S		 Switch layer for current trace
SHIFT
+ V		 Select favorite via size
SHIFT
+ W		 Open Choose Favorite Width dialog.
, (comma) Decrease arc setback
SHIFT
+ . (comma)		 Decrease arc setback 10x
. (full stop / period) Increase arc setback
SHIFT
+ . (full stop / period)		 Increase arc setback 10x
ENTER Place Segment
+ (plus) Next Layer (numeric keypad)
- (minus) Previous Layer (numeric keypad)
* (multiply) Next Signal Layer (numeric keypad)
SPACEBAR Cycle corner direction
SHIFT
+ SPACEBAR		 Cycle corner styles (if restrict to 90/45° is not enabled)
TAB Edit trace properties
1 Toggle Look-ahead Mode – Switches between 1 and 2 segment placement mode
2 Add via, no layer change
SHIFT
+ 2		 Add fanout via, tool immediately waits for next fanout to route and via to place
3 Cycle track width source
4 Cycle via size source
6 Force walk-around (with key pressed)
7 Switch leader trace or switch routing target in single trace mode
8 Toggle dynamic routing mode
9 Switches to opposite routing point
Copyright © dst 点击这里给我发消息